Category:Hardware & Tools/Fasteners & Connectors/Other Fasteners & Connectors

Product Description:Product Introduction:Solar-powered road studs, also known as raised pavement markers, are protrusive marking blocks fixed on the road surface to serve as road markings. They can be used on highways or other roads to mark centerlines, lane dividers, and edge lines; they can also be used to mark dangerous sections such as curves, entrance/exit ramps, channelizing lines, road narrowings, and road obstacles. Since solar road studs operate in synchronized flashing mode, they are commonly used for road edge lines, green belt outlines, lane width markings, etc. They are highly effective facilities for urban beautification, fog guidance, and enhanced road marking recognition. Powered by solar energy and utilizing wireless communication controllers, the light-emitting beads used are referred to as active light-emitting road studs.Product Name: Solar-Powered Road StudsModel: XH-TBDD-101ASpecifications: 115*100*22mmI. Technical Parameters:1. Energy storage component: NI-MH high-temperature resistant battery 1.2V-800MAH , charge-discharge cycles >1000 times, capacity not easily reduced;2. Solar charging battery: monocrystalline silicon 5V 30MA;3. Working time: Under standard light intensity, 8 hours of exposure can provide continuous operation for over 40 hours;4. Operating mode: Flashing (1Hz or 0.5Hz) , single-sided or double-sided;5. Display device: Ultra-bright LED , luminous intensity >3000mcd ( yellow, red) >5000mcd ( white);6. Light colors: Red, yellow, white, blue, green, etc.; Night visibility distance: 300 to 500 meters;7. Material: Cast aluminum shell + epoxy resin filling;8. Activation light intensity: Front illumination less than 500Lux;9. Operating environment: -20 ℃ to 70 ℃;10. Installation: Bonded with epoxy resin adhesive, can also be nailed for reinforcement, firm and stable, not easily detached; more>

Category:Hardware & Tools/Rolling Bearings/Other Bearings

Product Description:The working principle of Xiangye Environmental Dust Bearings is as follows:Through the design of components such as the support roller parts and base, the dust bearings can function to secure the rapping shaft in the electrostatic precipitator, preventing the rapping shaft from deviating or vibrating.Its special structural design helps extend its service life and facilitates installation, maintenance, and replacement.In theory, dust bearings do not serve a transmission function and may even affect transmission. Therefore, ensuring good lubrication on high-speed shaft bearings is essential.Dust bearings are specialized components used in electrostatic precipitators, primarily to secure the rapping shaft, prevent deviation and vibration, and ensure smooth rotation. Additionally, during rapping, they can expel dust that has entered the shaft hole outward with the rotation of the shaft, thereby improving the working environment of the rapping shaft.Structure of Dust BearingsDust bearings consist of the following parts:Support Roller Shaft: Features a narrow section in the middle, with retaining ring grooves and cotter pin holes at both ends.Support Roller: Cylindrical in shape, fits with the support roller shaft with clearance, and has grooves that match the sealing sleeve.Sealing Sleeve: Used to prevent dust from entering the bearing interior.Base: The base plate is rectangular, with fixed bolt holes at both ends and a rectangular hole in the middle for discharging dust. The side walls are symmetrical, with features such as inclined slots, locking sleeve holes, and pin shaft installation holes.Other Accessories: Include shims, locking sleeves, cotter pins, pin shafts, retaining rings, and protective covers.Production of various specifications of rapping hammers, dust bearings, anode plates, spike electrodes, etc.Common types include: bent arm rapping hammers, straight arm rapping hammers, anode rapping hammers, cathode rapping hammers, bean sprout hammers, etc. Custom-made special-shaped rapping hammers are also available. more>

Category:Hardware & Tools/Cutting Power Tools/Drill Bits

Product Description:1.Overview:The JCP series grape destemmer and crusher products are newly developed by our company, incorporating advanced technologies from similar machines in France and Italy, and tailored to the conditions of our country. They can produce large models with a capacity of 2-50 tons per hour.2.Performance Features:1.Spiral quantitative feeding, destemming first then crushing2.Both the destemming shaft and the destemming rotating screen can achieve stepless speed variation (now granted a utility model patent, Patent No.: ZL2001 2 004425803), adaptable to processing various grape varieties, with minimal grape loss in the stems discharged from the machine.3.The crushing device is located below the destemming rotating screen. The crushing rollers are made of highly elastic non-toxic rubber. The crushing device is connected to the main body via a quick-open mechanism, with a crushing rate above 93%.4.The pulp transfer pump is a single screw pump, installed below the crushing device, with a feed hopper equipped with a liquid level control device.The rotating screen has an aperture of 28 mm. If the grape berries are too large or too small, please specify when ordering. more>

Category:Hardware & Tools/Castings/Iron Castings

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. This has been the operational philosophy upheld by our factory for over a decade.Our main products include:1. Flap gates, categorized into: cast iron, steel, composite materials. Composite flap gates often refer to FRP (fiberglass reinforced plastic) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw hoists, categorized into: flat push type, handwheel type, side crank type, manual type, electric type, dual manual-electric type, direct-connected type, single and double lifting point screw hoists.3. Winch hoists, categorized into: gantry type, mobile type, radial gate type (models include QPQ, QPK, QPT, QHQ), available in various models and specifications from 5T to 250T for both single and double lifting points.4. Debris cleaning equipment series, including: stainless steel fine bar screens with specific gap widths, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for waters with relatively high head, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates: Available in over sixty specifications from 0.2m × 0.2m to 6.5m × 6.5m, widely used in hydropower stations, reservoirs, agricultural water conservancy, and sewage treatment plants.7. Steel gates and stainless steel gates: Mainly used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally sound, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber strips.Our enterprise sincerely cooperates with both new and existing customers through excellent product quality, warm and attentive service, and reasonable product pricing. more>

Category:Hardware & Tools/Fasteners & Connectors/Other Fasteners & Connectors

Product Description:Product Introduction:Product Name: Cast Aluminum Solar Road StudSpecifications: 115*100*22mmII. Functions and Roles:1. Light-emitting studs mainly refer to active light-emitting solar road studs. Solar road studs use solar energy to power LEDs, emitting various types of light to prompt and guide vehicles safely. They are primarily installed on special road sections such as curves and foggy areas, flashing at a certain frequency to attract the attention of drivers and passengers.2. Combination studs integrate reflective and active light-emitting features, representing a new type of cast aluminum road stud product developed in recent years.3. Cast aluminum solar road studs protrude from the road surface, creating vibration when vehicles pass over them, providing appropriate alerts to drivers and passengers. They are widely used on lane edge lines, lane boundaries where frequent lane changes are not allowed, road entrances/exits, and roads where vehicles need to slow down. more>

Category:Hardware & Tools/Castings/Iron Castings

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. This has been the operational philosophy upheld by our factory for over a decade.Our main products include:1. Flap gates, which are categorized into: cast iron, steel, composite materials. Composite flap gates often refer to fiberglass reinforced plastic (FRP) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw lift gates are divided into: flat push type, handwheel type, side crank type, manual type, electric type, dual manual-electric type, direct connection type, single and double lifting point screw lift gates.3. Hoist gates are categorized into: gantry type, mobile type, radial gate type (including models such as QPQ, QPK, QPT, QHQ), ranging from 5T to 250T, with single and double lifting points among various models and specifications.4. Debris cleaning equipment series include: stainless steel fine bar screens with specific gap widths, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for waters with relatively high heads, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates: Available in over sixty specifications from 0.2m × 0.2m to 6.5m × 6.5m, commonly used in hydropower stations, reservoirs, agricultural water conservancy, and sewage treatment plants.7. Steel gates and stainless steel gates: Primarily used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally sound, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber strips.Our enterprise sincerely collaborates with both new and existing customers, offering superior product quality, enthusiastic and attentive service, and reasonable product pricing. more>

Category:Hardware & Tools/Castings/Iron Castings

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. For over a decade, our factory has adhered to the following operational philosophy.Our main products include:1. Flap gates, which are categorized into: cast iron, steel, composite materials. Composite flap gates often refer to FRP (fiberglass reinforced plastic) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw lift gates are divided into: flat push type, handwheel type, side crank type, manual type, electric type, manual-electric dual-use type, direct connection type, single and double lifting point screw lift gates.3. Winch hoists are categorized into: gantry type, mobile type, radial gate type (QPQ, QPK, QPT, QHQ), with models ranging from 5T to 250T for both single and double lifting points.4. Debris cleaning equipment series include: stainless steel fine bar screens with specific gap widths, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for waters with relatively high heads, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates are available in over sixty specifications from 0.2m×0.2m to 6.5m×6.5m, commonly used in hydropower stations, reservoirs, agricultural water conservancy, and sewage treatment plants.7. Steel gates and stainless steel gates: Primarily used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally sound, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber strips.Our enterprise sincerely cooperates with both new and existing customers through excellent product quality, warm and attentive service, and reasonable product pricing. more>

Category:Hardware & Tools/Castings/Iron Castings

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. This has been the operational philosophy upheld by our factory for over a decade.Our main products include:1. Flap gates, which are categorized into: cast iron, steel, composite materials. Composite flap gates often refer to FRP (fiberglass reinforced plastic) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw hoists, which are divided into: flat push type, handwheel type, side crank type, hand-operated type, electric type, dual-purpose hand-electric type, direct-connected type, single and double lifting point screw hoists.3. Winch hoists, which are categorized into: gantry type, mobile type, radial gate type (QPQ, QPK, QPT, QHQ), available in various models and specifications from 5T to 250T for both single and double lifting points.4. Debris cleaning equipment series, which include: stainless steel fine bar screens with narrow gaps, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for water bodies with relatively high heads, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates: Available in over sixty specifications ranging from 0.2m × 0.2m to 6.5m × 6.5m, widely used in hydropower stations, reservoirs, agricultural water conservancy, and sewage treatment plants.7. Steel gates and stainless steel gates: Primarily used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally sound, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber strips.Our enterprise sincerely cooperates with both new and existing customers by offering high-quality products, warm and attentive service, and reasonable product prices. more>

Category:Hardware & Tools/Castings/Iron Castings

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. This has been the operational philosophy our factory has adhered to for over a decade.Our main products include:1. Flap gates, which are categorized into: cast iron, steel, composite materials. Composite flap gates often refer to FRP (fiberglass reinforced plastic) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw lift hoists, which are divided into: flat push type, handwheel type, side crank type, hand crank type, electric type, dual-purpose hand-electric type, direct-connected type, single and double lifting point screw lift hoists.3. Winch hoists, which are categorized into: gantry type, mobile type, radial gate type (models such as QPQ, QPK, QPT, QHQ), available in various models and specifications from 5T to 250T for both single and double lifting points.4. Debris cleaning equipment series, which include: stainless steel fine bar screens with specific gap clearances, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for waters with relatively high head, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates: Available in over sixty specifications from 0.2m × 0.2m to 6.5m × 6.5m, widely used in hydropower stations, reservoirs, farmland water conservancy, and sewage treatment plants.7. Steel gates and stainless steel gates: Mainly used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally rational, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber belts.Our enterprise sincerely cooperates with both new and existing customers through excellent product quality, warm and attentive service, and reasonable product pricing. more>

Category:Hardware & Tools/Castings/Iron Castings

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. For over a decade, our factory has adhered to the following operational philosophy.Our main products include:1. Flap gates, which are categorized into: cast iron, steel, composite materials. Composite flap gates often refer to fiberglass reinforced plastic (FRP) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw lift gates are divided into: flat push type, handwheel type, side crank type, manual type, electric type, manual-electric dual-use type, direct connection type, single lifting point, and double lifting point screw lift gates.3. Winch hoists are categorized into: gantry type, mobile type, radial gate type (QPQ, QPK, QPT, QHQ), available in various models and specifications from 5T to 250T, including single and double lifting points.4. Debris cleaning equipment series include: stainless steel fine bar screens with specific gap widths, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for waters with relatively high heads, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates are available in over sixty specifications ranging from 0.2m×0.2m to 6.5m×6.5m, commonly used in hydropower stations, reservoirs, agricultural water conservancy, and sewage treatment plants.7. Steel gates and stainless steel gates: Primarily used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally rational, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber strips.Our enterprise sincerely cooperates with both new and existing customers through excellent product quality, warm and attentive service, and reasonable product pricing. more>

Category:Hardware & Tools/Castings/Iron Castings

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. For over a decade, our factory has adhered to its operational philosophy.Our main products include:1. Flap gates, categorized into: cast iron, steel, composite materials. Composite flap gates often refer to FRP (fiberglass reinforced plastic) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw lift gates, categorized into: flat push type, handwheel type, side crank type, manual type, electric type, manual-electric dual-use type, direct connection type, single and double lifting point screw lift gates.3. Hoist gates, categorized into: gantry type, mobile type, radial gate type (QPQ, QPK, QPT, QHQ), available in various models and specifications from 5T to 250T, including single and double lifting points.4. Debris cleaning equipment series, including: stainless steel fine bar screens with specific gap widths, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for waters with relatively high heads, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates: Available in over sixty specifications from 0.2m×0.2m to 6.5m×6.5m, commonly used in hydropower stations, reservoirs, agricultural water conservancy, and sewage treatment plants.7. Steel gates, stainless steel gates: Mainly used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally rational, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber strips.Our enterprise sincerely cooperates with both new and existing customers, offering high-quality products, warm and attentive service, and reasonable product prices. more>

Category:Hardware & Tools/Rolling Bearings/Other Bearings

Product Description:Xiangye Editor introduces the characteristics of dust-bearing types: mainly including roller-type rolling bearings and integral sliding bearings. In roller-type rolling bearings, the two-wheel type cannot withstand upward force and is only suitable for downward force applications; the three-wheel and four-wheel types can be used in scenarios with both downward and upward forces. The integral sliding dust-bearing has a simple structure, is cast as a whole, and is suitable for various force conditions.<img src="https://img-i-album.toocle.com/view/2025/09/10/7d/68c1363cce67d.jpg" style="max-width:100%;"/> ? Dust-proof design: Some dust-bearings are equipped with soft dust-proof fabric on both sides of the integral bearing, with clamps applied outside the fabric to prevent or reduce dust from entering the bearing hole, thereby reducing wear and extending service life. ? Installation and maintenance: The structural design of dust-bearings allows all components to be easily and quickly assembled and disassembled, making installation, repair, and replacement very convenient. During maintenance, regular cleaning is required to remove surface-adhered particles. After cleaning, anti-rust grease should be applied immediately. Additionally, weight, dimensions, and rotational accuracy should be checked regularly, and replacement is necessary if standards are not met.<img src="https://img-i-album.toocle.com/view/2025/09/10/8d/68c1364b57b8d.jpg" style="max-width:100%;"/>Working PrincipleThe working principle of dust-bearings is as follows:Through the design of components such as rollers and supports, dust-bearings can function in electrostatic precipitators to secure the rapping shaft and prevent misalignment and bouncing.Their special structural design helps extend service life and facilitates installation, repair, and replacement.In theory, dust-bearings do not serve a transmission function and may even interfere with it. Therefore, ensuring good lubrication on high-speed shaft bearings is essential. more>

Category:Hardware & Tools/Rolling Bearings/Other Bearings

Product Description:HT, JZ Series Friction False Twister Drive and Driven Bearing Products<img/>HT825 and other bearingsDimensions / ModelLoL1LHhIDD1dMZZ1RemarksFigure 1, Figure 4HT821-11001874543.85915.261.5232812520With tension ring, Figure 4HT821-120013843.85915.261.52312520HT825-11001874543.85915.261.5232812520HT825-120013843.85915.261.52312520HT825F-11002164543.85915.290.5232812520HT825F-120016743.85915.290.523125極> more>

Category:Hardware & Tools/Cutting Power Tools/Drill Bits

Product Description:Xinhe County Jiangfan Water Conservancy Machinery Factory is a comprehensive manufacturer in the hydraulic machinery industry, integrating manufacturing, metal structures, casting, machining, heat treatment, and final assembly. This has been the operational philosophy our factory has adhered to for over a decade.Our main products include:1. Flap gates, which are categorized into: cast iron, steel, composite materials. Composite flap gates often refer to FRP (fiberglass reinforced plastic) flap gates, available in various models and specifications from 200mm to 2600mm.2. Screw hoists, which are divided into: flat push type, handwheel type, side crank type, hand crank type, electric type, dual-purpose hand-electric type, direct-connected type, single and double lifting point screw hoists.3. Winch hoists, which are categorized into: gantry type, mobile type, radial gate type (models include QPQ, QPK, QPT, QHQ), with lifting capacities ranging from 5T to 250T, available in single and double lifting point configurations.4. Debris cleaning equipment series, which include: stainless steel fine bar screens with specific gap widths, trash racks, toothed rotary screen cleaners, rotary screen cleaners, GLGS high-chain type screen cleaners, YZL type spiral presses, XGS rotary screen cleaners, HZG rotary screen cleaners, and conveyors.5. Cast iron (composite) gates: Suitable for waters with relatively high head, such as hydropower stations and reservoirs.6. Cast iron (bronze-inlaid) gates: Available in over sixty specifications from 0.2m×0.2m to 6.5m×6.5m, widely used in hydropower stations, reservoirs, agricultural water conservancy, and sewage treatment plants.7. Steel gates and stainless steel gates: Primarily used for environmental protection and sewage treatment.8. The Yuanshuo brand series of gates produced by our factory are safe to use, structurally sound, and perform excellently.9. Various specifications of waterstop rubber and expansion joint elastic rubber strips.Our enterprise sincerely cooperates with both new and existing customers by offering high-quality products, warm and attentive service, and reasonable product prices. more>

Category:Hardware & Tools/Rolling Bearings/Other Bearings

Product Description:The dust-bearing is an important accessory of the electrostatic precipitator. Below is a detailed introduction about it:Structural Composition: The dust-bearing consists of a support wheel assembly formed by a support wheel shaft, support wheels, and sealing sleeves, as well as support seats, gaskets, locking sleeves, split pins, pin shafts, retaining rings, protective covers, etc. The support wheels are cylindrical, with a clearance fit to the support wheel shaft, and are equipped with grooves that match the sealing sleeves. The support wheel shaft has a narrow section in the middle, with retaining ring grooves and split pin holes at both ends. The base plate of the support seat is rectangular, with fixed bolt holes at both ends and a rectangular hole in the middle for discharging dust. The side plates are symmetrical, featuring inclined slots, locking sleeve holes, and pin shaft installation holes.<img src="https://img-i-album.toocle.com/view/2025/09/10/60/68c133aae4560.jpg" style="max-width:100%;"/>Working Principle: The dust-bearing is mainly used to support the rapping shaft of the electrostatic precipitator, bearing radial loads. It ensures that the rapping shaft rotates in place without any lateral or longitudinal movement, guaranteeing the normal operation of the rapping shaft and thereby achieving the rapping and cleaning of the precipitator's plates and wires.<img src="https://img-i-album.toocle.com/view/2025/09/10/ac/68c133cb98cac.jpg" style="max-width:100%;"/>Structure of the Dust-BearingThe dust-bearing consists of the following components:Support Wheel Shaft: Features a narrow section in the middle, with retaining ring grooves and split pin holes at both ends.Support Wheels: Cylindrical in shape, with a clearance fit to the support wheel shaft, and equipped with grooves that match the sealing sleeves.Sealing Sleeves: Used to prevent dust from entering the interior of the bearing.Support Seat: The base plate is rectangular, with fixed bolt holes at both ends and a rectangular hole in the middle for discharging dust. The side plates are symmetrical, featuring inclined slots, locking sleeve holes, and pin shaft installation holes.Other Accessories: Include gaskets, locking sleeves, split pins, pin shafts, retaining rings, protective covers, etc. more>

Category:Hardware & Tools/Rolling Bearings/Other Bearings

Product Description:Xiangye Environmental Dust Bearings (Electrostatic Precipitator) Two-Wheel/Three-Wheel 50/60 Model Analysis1. Model Classification and SpecificationsTwo-Wheel Dust Bearings: Labeled as "Two-Wheel," with shaft diameter specifications of 50mm or 60mm, suitable for two-wheel rapping systems in electrostatic precipitators.Three-Wheel Dust Bearings: Labeled as "Three-Wheel," also supporting 50/60mm shaft diameters, compatible with three-wheel rapping structures, commonly used in large electrostatic dust removal equipment.<img src="https://img-i-album.toocle.com/view/2025/10/23/f8/68f992f0186f8.jpg" style="max-width:100%;"/>2. Technical FeaturesDustproof Design: Utilizes sealed structures or electrostatic dust removal technology to reduce dust intrusion and extend bearing lifespan.Material: Typically made of high-strength alloy steel or corrosion-resistant stainless steel, suitable for high-temperature, high-dust environments.3. Application ScenariosElectrostatic Precipitators: Used to support rapping shafts, ensuring stable operation of the cathode/anode ash cleaning system.<img src="https://img-i-album.toocle.com/view/2025/10/23/cd/68f992de30acd.jpg" style="max-width:100%;"/>Industrial Environments: Such as cement plants, steel mills, and other dust-intensive locations.4. Selection RecommendationsChoose between two-wheel or three-wheel models based on rapping shaft diameter (50mm or 60mm) and load requirements.<img src="https://img-i-album.toocle.com/view/2025/10/23/12/68f992ffd9612.jpg" style="max-width:100%;"/>It is recommended to use with the same series of rapping hammers (e.g., φ120 model) to ensure system compatibility.For specific parameters or purchasing links, further details such as equipment drawings or working conditions can be provided by Xiangye Environmental. more>